销售热线 400-812-0328  |  微信同号 13798439218  |  WhatsApp +85251628371
欢迎光临本店 请登录  |  免费注册
当前位置: 首页 > 柯斯摩尔动态 > CosMolar Semi-Automatic Foaming Machine Operation Manual
CosMolar Semi-Automatic Foaming Machine Operation Manual
柯斯摩尔官网 / 2026-09-03

1. What Is This

The CosMolar Semi-Automatic Foaming Machine (CM-811) is an electric on-site foaming packaging device that requires no air source — just plug into a 220V power supply and it's ready. It heats the A and B foaming raw materials, mixes them in proportion, and dispenses them through the spray gun. The foam expands and hardens within tens of seconds, tightly wrapping the product to protect it from shock, impact, and scratches. Ideal for packaging: electronic components, instruments and meters, auto parts, motors and pumps, ceramic handicrafts, irregular-shaped parts, and medium-to-large batch shipping.

2. Before You Start

  • Power: 220V, 32A single-phase supply (peak power 3500W); keep the power outlet within 3m of the main unit.
  • Materials: Make sure the A and B drums have material and the pumps are fitted correctly — A pump into the A drum, B pump into the B drum. Do not mix them up.
  • Placement: Keep the material drums within 1.5m of the main unit; mount the main unit about 1.5m above the floor with working space around it.
  • Inspection: Check the material hoses and power cables for damage, and the spray gun nozzle for cleanliness.

3. Four Steps to Start Up

Step 1 · Power On and Preheating

Push up the blue switch on the right side of the main unit to power on. The touchscreen shows "System Detecting". After about 2 minutes it shows "System Ready" — the material inside the hoses has reached the target temperature.

Step 2 · Choose a Mode

Tap the screen once to enter the main interface. You MUST choose a mode (tap the mode box to turn it green), otherwise no material will be dispensed. Two modes are enough for daily use:

  • Manual Continuous Mode (factory default): press and hold the gun trigger to dispense, release to stop. Ideal for small quantities and occasional use.
  • Fixed Time Mode: enter the dispense time, press the trigger once and it automatically dispenses for the programmed time, then stops. Ideal for repeatedly packaging the same product.

Step 3 · Test Spray

First test-spray into a waste carton or waste bag to confirm the foam is normal, evenly colored, and fully expanded, before formal use.

Step 4 · Formal Foaming

Follow the "Four Steps of On-Site Foam Packaging" below. After dispensing, place the gun nozzle back into the gun-holder box and brush it to keep the nozzle clean.

4. Four Steps of On-Site Foam Packaging

  1. Line the Box and Spray the Base: Lay high-strength packaging film into the carton and spray an appropriate amount of foaming liquid onto the film.
  2. Place the Product: Fold the film over and place the product onto the expanding foam so the foam fits the product's bottom.
  3. Cover and Spray the Top: Lay another layer of film on top of the product and spray foaming material to wrap the product's top.
  4. Close the Box and Ship: Close the carton, wait briefly for the foam to harden, then seal and ship directly.

Tip: Do not spray material onto foam that is still expanding — it will damage the foam structure. When making pre-formed foam cushions with a mold, use "Fixed Time Mode" so every cushion is the same size.

5. Daily Maintenance (Three Simple Things)

  1. Spray Gun Nozzle: After each use, put the nozzle back into the gun-holder box and brush it with the steel brush to keep it clean.
  2. Gun-Holder Box: When the liquid level falls below the top of the box, add gun-holder liquid in time (about 2mm above the top of the steel brush). Replace the steel brush when it bends, deforms, or wears out.
  3. Changing Material Drums: When low-material is indicated — turn off the main power first, place the full drum beside the empty one, open the new drum's lid, pull the material pump out of the empty drum and immediately place it into the full drum. Note: the A pump only goes into the A drum, the B pump only into the B drum; do not leave the pump out of the drum for long, otherwise the material will harden and permanently damage the pump.

6. Precautions

  • Turn off the main power before maintenance or repair; non-professionals should not open the main control box or material pump box to avoid electric shock.
  • Wear safety goggles and gloves when cleaning the nozzle; if foaming material touches skin, rinse immediately with clean water.
  • Wrap the joint between the red drum (A material) opening and the pump with waterproof tape or stretch film to reduce air flow that causes A material crystallization.
  • Do not leave the red drum (A material) empty for too long: keep the A pump immersed in the A liquid at all times and do not pull it out in daily use; only when changing drums, pull the pump out of the empty drum and immediately place it into the full drum.
  • Never turn the material pump upside down — material will flow into the pump motor and cause serious damage.
  • Do not spray material onto expanding foam — it will damage the foam structure and affect expansion.
  • Use CosMolar original materials, films, and parts; mixing with other materials may affect foaming results and after-sales warranty.
  • Store material drums in a cool, dry place, away from fire and heat sources.
  • If you encounter problems you can't solve, contact CosMolar directly: 400-812-0328 / 0755-27807490, website www.CosMolar.com.

The CosMolar Semi-Automatic Foaming Machine CM-811 — no air source, plug-and-play with 220V, fast foaming, stable molding, saving time and effort for medium-to-large batch packaging. From hand-slap foam bags and semi-automatic to fully automatic foaming machines, CosMolar provides complete on-site foam packaging solutions and raw materials — one-stop packaging.

用户评论(共0条评论)

  • 暂时还没有任何用户评论
总计 0 个记录,共 1 页。 第一页 上一页 下一页 最末页
用户名: 匿名用户
E-mail:
评价等级:
评论内容:
验证码: captcha