销售热线 400-812-0328  |  微信同号 13798439218  |  WhatsApp +85251628371
欢迎光临本店 请登录  |  免费注册
当前位置: 首页 > 柯斯摩尔动态 > CosMolar Fully Automatic Foaming Machine Operation Manual
CosMolar Fully Automatic Foaming Machine Operation Manual
柯斯摩尔官网 / 2026-09-03

1. What Is This

The CosMolar Fully Automatic Foaming Machine (CM-812) is an electric on-site foaming packaging system that needs no air source — just plug into a 220V power supply and it's ready. It heats the A and B raw materials, mixes them in the right proportion inside the gun nozzle, and the two react to form high-quality polyurethane foam that is automatically filled into foam bags of your chosen size. The finished bags go straight onto your products for shipping. Ideal for packaging: automotive headlights, electronic components, instruments and meters, motors and pumps, irregular-shaped parts, and products that need fast, batch packaging.

2. Before You Start

  • Power: 220V, 32A single-phase supply; keep the power outlet within 3m of the main unit.
  • Materials: Make sure the A and B drums have material and the pumps are fitted correctly — A pump into the A drum, B pump into the B drum. Do not mix them up.
  • Placement: Keep the material drums within 5m of the main unit; mount the main unit about 1.5m above the floor, with open space in front of the main unit and the power outlet.
  • Inspection: Check the material hoses and power cables for damage, and the gun nozzle for cleanliness.

3. Four Steps to Start Up

Step 1 · Power On

Turn on the power switch below the touchscreen box. The screen shows the system status and automatically moves to the self-check screen.

Step 2 · Two Checks

Follow the on-screen prompts and tap the red boxes "Gun-Immersion-Liquid Check" and "Sealing Check" one by one; once both pass, the machine is ready. Note: for the new model, only the "Sealing Check" is needed.

Step 3 · Choose a Mode

Tap to enter the "Production Screen" or "Tubular Foaming Screen":

  • Free-Size Foam Bag Mode: choose the carton size, enter the bag length for your product, the fill percentage and the number of bags required — the machine automatically makes foam bags of the matching size. Ideal for most products.
  • Tubular Foaming Mode: enter the tube spacing, length and number — the machine makes a connected chain of tubular foam bags. Ideal for special tube-shaped products.

Step 4 · Production

Choose the parameters, tap "Start", and the machine automatically produces bags. (Temperature, flow and pressure are pre-adjusted by the factory; no daily changes are needed.)

4. Four Steps of Foam Packaging

  1. Prepare: Get the product and carton ready, choose the matching parameters on the screen and tap "Start".
  2. Bag Output: The machine automatically produces a foam bag of the right size (free-size bag or tubular bag).
  3. Pack: Put the foam bag into the carton, place the product inside, and let the foam wrap around the product.
  4. Seal and Ship: Wait for the foam to harden, then close and seal the carton and ship.

Tip: When making pre-formed foam cushions with a mold, use the timed mode so every cushion is the same size (in a hot mold, use about 5% less fill time than in a cold mold).

5. Daily Maintenance (Three Simple Things)

  1. Gun Nozzle: When foaming is abnormal or a fault occurs, clean the nozzle in time and replace the sealing parts (O-rings, etc.).
  2. Regular Checks: Check the spray gun, gun filter, material hoses and system parts once a month; check the level of consumables once a week.
  3. Changing Material Drums: When the screen warns of low material — turn off the main power first, place the full drum beside the empty one, open the new drum's lid, inspect and clean the pump bottom filter (rinse it with gun-cleaning liquid), pull the material pump out of the empty drum and immediately place it into the full drum. Note: the A pump only goes into the A drum, the B pump only into the B drum; do not leave the pump out of the drum for long, otherwise the material will harden and permanently damage the pump.

6. Precautions

  • Turn off the main power before maintenance or repair; non-professionals should not open the main control box or material pump box to avoid electric shock.
  • Never turn the material pump upside down — material will flow into the pump motor and cause serious damage.
  • If a pump is plugged into the wrong drum (e.g., the A pump into the B drum), do NOT start the machine; contact CosMolar immediately.
  • Wrap the joint between the red drum (A material) opening and the pump with waterproof tape or stretch film to reduce air flow that causes A material crystallization.
  • Do not leave the red drum (A material) empty for too long: keep the A pump immersed in the A liquid at all times; only when changing drums, pull the pump out and immediately place it into the full drum.
  • Use CosMolar original materials, films, and parts; mixing with other materials may affect foaming results and after-sales warranty.
  • Store material drums in a cool, dry place, away from fire and heat sources.
  • If you encounter problems you can't solve, contact CosMolar directly: 400-812-0328 / 0755-27807490, website www.CosMolar.com.

The CosMolar Fully Automatic Foaming Machine CM-812 — no air source, plug-and-play with 220V, fully automatic bag output, saving time and effort for batch packaging. From hand-slap foam bags and semi-automatic to fully automatic foaming machines, CosMolar provides complete on-site foam packaging solutions and raw materials — one-stop packaging.

用户评论(共0条评论)

  • 暂时还没有任何用户评论
总计 0 个记录,共 1 页。 第一页 上一页 下一页 最末页
用户名: 匿名用户
E-mail:
评价等级:
评论内容:
验证码: captcha