销售热线 400-812-0328  |  微信同号 13798439218  |  WhatsApp +85251628371
欢迎光临本店 请登录  |  免费注册
当前位置: 首页 > 行业资讯 > Why Is 6 kg/m3 the Standard Foam Density? Three Densities Explained
Why Is 6 kg/m3 the Standard Foam Density? Three Densities Explained
CosMolar / 2026-10-24

Start

Many first-time buyers ask: you offer several foam densities, which one should I choose? Why do most people use 6 kg/m3? Today we break down the three densities, what products each suits, and how to pick the right one.

First: how does density relate to cost?

A common misconception: higher density means better material. Actually, it works the other way. Lower density means higher expansion ratio — the same weight of material fills more volume, so you use less material per box and the unit cost is lower. Higher density means lower expansion ratio, you use more material per box, and the cost is higher.

But higher density is not useless — it has higher physical strength, better load-bearing capacity, and firmer protection. So choosing density is not about picking the highest or lowest, it is about matching what your product needs.

6 kg/m3 standard: the all-rounder, used by 80% of customers

This is CosMolar's best-selling and most widely used density. Why call it the standard? Because it balances everything: high expansion ratio means lowest material cost, soft texture after curing gives good cushioning without damaging delicate surfaces, and it cures in 3-5 seconds.

What products? The vast majority of irregular fragile parts: automotive components, pumps and valves, motors, crafts, LED lights, electronics, glass and ceramics — anything not especially heavy works with 6 kg/m3.

If you are not sure which density to pick, start with 6 kg/m3 sample testing. It works for about 80% of use cases.

17 kg/m3 medium: for medium-weight products needing support

For products weighing 5-15 kg, or when the bottom layer needs firm support, choose 17 kg/m3. It is firmer than 6 kg/m3 with better load-bearing, but slightly less cushioning softness.

What products? Medium motors, gearboxes, small machine tool parts, medium-weight equipment components — products with some weight but not heavy enough to need high-density support. In practice, many customers combine densities: spray 17 kg/m3 on the bottom for load-bearing, then 6 kg/m3 on top and sides for cushioning — strong base, soft cushion.

23 kg/m3 high-density: for heavy products needing firm support

For products over 15 kg, or when the bottom needs a very firm support layer, choose 23 kg/m3. It cures firm, with the highest load-bearing capacity — heavy products will not crush the foam base.

What products? Heavy motors and gearboxes, cast iron pump bodies, large equipment parts, machine tool spindles — heavy products where the bottom needs strong support. Spray 23 kg/m3 on the bottom as the load-bearing base, then combine with 6 kg/m3 on top and sides for cushioning.

Note: high-density foam has lower expansion ratio, so you use more material and the unit cost is higher. That is why you do not spray high-density everywhere — only on the bottom load-bearing layer, with low-density foam for cushioning on the sides and top. This saves cost while maintaining protection.

A simple rule for choosing:

Under 5 kg: use 6 kg/m3 directly, the all-rounder.

5-15 kg: bottom 17 kg/m3 load-bearing + top 6 kg/m3 cushioning, combined.

Over 15 kg: bottom 23 kg/m3 load-bearing + top 6 kg/m3 cushioning, combined.

Not sure which fits your product? Contact CosMolar for free sample testing. Learn more at https://www.cosmolar.com/

用户评论(共0条评论)

  • 暂时还没有任何用户评论
总计 0 个记录,共 1 页。 第一页 上一页 下一页 最末页
用户名: 匿名用户
E-mail:
评价等级:
评论内容:
验证码: captcha